Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - studiobasler

Pages: 1 2 [3]
31
[C4D] General Discussion / Re: Render Big Resolution
« on: 2017-12-06, 10:37:55 »
thank you, baking will be the next thing i would try.

So what would you suggest when it comes to render such big sizes. I noticed that even with a simple setup, for example a cube and 2 lights, it takes so much more time to render. I dindt work with vray for a long time, but i remember that there was not such a big time shift when it comes to render big sizes. Is this a point which will need more development or am i doing something totally wrong?

32
[C4D] General Discussion / Re: Fireflies
« on: 2017-12-05, 23:03:49 »
thank you for your advise, i end up with rendering this region again, which gave me a better result. Thank you all.

33
[C4D] General Discussion / Render Big Resolution
« on: 2017-12-05, 23:01:32 »
Hello Forum,
i do have to render a scene in 20k and  unfortunately i get error messages all the time which say 'to less ram'. I have 128 gb of ram in my machine but i cant render higher than 13K.
The scene is nothing special. Its a parkdeck with some pillars, a floor and some walls. Two of the Materials have displacement material. I do have about 15 light sources and one hdri as my main light. I put all the lights in the multipass light mix selection and applied denoising to them. So usually i render in Corona vfb and save out my images as exr. Is this the way to go or is it better to use c4d picture viewer instead?

Any suggestions would be very fine, thank you.

Cheers
Christian

34
[C4D] General Discussion / Re: Fireflies
« on: 2017-11-26, 20:35:44 »
i will give it a try. Thank you man...

35
[C4D] General Discussion / Re: Fireflies
« on: 2017-11-22, 12:49:13 »
yes for sure, im usin a full denoising with a value of 0.5

36
[C4D] General Discussion / Fireflies
« on: 2017-11-22, 11:21:47 »
Hello,
i cant get rid of these fireflies. Im using a hdr environment to lit my scene. Everything else is perfect but i cant reduce noise/firelfies in this area. I reduce max sample intensity to 15 checked my glass material and i cannot find any issues. Im using a light material for the car lights with an intensity of 4. Any tips what i can do next? Noise Level is about 1.9%. after two hours of rendering.

Cheers Christian

37
[C4D] General Discussion / Re: Light Mix Units and Denoising
« on: 2017-10-25, 12:34:58 »
Hello maru,
yes uploaded the file yesterday, i thought you would be informed automaticly. Because of File size i uploaded it into my dropbox: Christian Basler - CoronaExport.rar
Did you get any further information on that?

Cheers
Christian 

38
[C4D] General Discussion / Re: C4D - Black Render
« on: 2017-10-24, 20:42:56 »
Did you activate Bloom and Glare? I had the same Problem, and unchecking it brought back my Beauty Pass

39
[C4D] General Discussion / Re: Light Mix Units and Denoising
« on: 2017-10-24, 18:34:22 »
just uploading, thanks. Can you also check the LightMix Issue?

Thank you
Christian

40
[C4D] General Discussion / Re: Light Mix Units and Denoising
« on: 2017-10-24, 15:34:03 »
ok, but there isnt any RC9 for C4D or am i wrong?

41
[C4D] General Discussion / Re: Light Mix Units and Denoising
« on: 2017-10-24, 13:19:24 »
Thanks you both for your input.
I did a test with the light mix, but it has no effect. First i render the image and do my adjustments in LightMix. Then i click ">Scene" and re render the image, but there arent any changes. All my settings in the LightMix are gone to 1 and in the rerendered image are the same light intensitys as before.

Further on i get these "black fireflies" and i have no idea why. At the beginning of the render process there arent any of these black dots, but later on they appear suddenly. If i remove the Light sources, the black dots do not appear. Maybe my light sources have to much intensity (Lumen 5000)?

Cheers


42
[C4D] General Discussion / Light Mix Units and Denoising
« on: 2017-10-23, 12:23:38 »
Hello Forum,
so Iam new to Corona and first of all its very intuitiv and im happy with my first results.
Raising up the Light mix Values ends up in a very noisy image althought i checked the "Apply denoising" to it.
So im using Light mix to find the corrct light intensity and would like to know the corresponging units so i'am able to
feed my lumen Value. If i raise up the Light Mix value for example to 6, what value do i have to insert in my lumen intensity to get the same intensity?

Thank you
Christian

Pages: 1 2 [3]