Messages

16

Hardware / Re: Threadripper & Ryzen builds

« on: 2025-01-15, 17:19:24 »

I'm going to have to see, It was boosting all the way till it hit the higher temps with the other cooler. This XE360-TR5 is pretty damn nice. I was reading about the IceGiant ProSiphon Titan-TR 360 a couple of days ago, have to see real benchmarks with it. My system board sit horizontal and this won't work with it, but I hear they are developing on for horizontal motherboards.

17

[Max] I need help! / Re: GI Flickering in animation

« on: 2025-01-14, 17:39:23 »

Okay, I'll get the scene together. It's quite large!

18

Hardware / Re: Threadripper & Ryzen builds

« on: 2025-01-14, 16:18:01 »

I wanted to get you guys feedback on this.  One of my 7980x systems had it's AIO Fail. It was running a Silverstone IceGem 360, I set it to overclocked and a temperature limit of 80c. It ran super fast and like clockwork. one day during rendering an animation the entire system shut down. I found the system off and looked into it. I think it shut itself down for safety issues to temp. Running Corona bench I could see temps would quickly climb to 95c telling me the AIO is now dead. So I replaced it with a Silverstone XE360-TR5. The XE360-TR5 cooling is incredible, but almost feels like too good like there is an issue with the system or something. I also notice the system will not boost higher even though the temps are only reaching 66.8c. SO it's hard to believe the temps are only 66.8c and that the system will not boost and higher. what do you guys think? I'm just hoping I didn't damage the motherboard or cpu. I attached a screen shot below of temps and Corona bench.

I did already clear cmos and even upgraded the Bios.

19

[Max] I need help! / GI Flickering in animation

« on: 2025-01-14, 15:50:05 »

I wanted to see what everyone thought before I decide if this is something I should send to Chaos as a bug of some sorts. I use primarily 4k for secondary like I did a long time ago, but now I get Flickering in GI on a lot of scenes. Back in the day I switched from UHD to 4K because I was getting much faster calculations and better quality. I never got flickering from 4K before. I tried same scenes with UHD, and am getting much less flickering but still on some scenes still getting really bad flickering. Working on really big scenes now and in the past I can confidently say this was really never an issue before. Seems like with the newest Corona I'm having a lot of GI flickering issues, am I the only one?

Corona 12 Update 1
Max 2025.3
Tried 4k & UHD
Set to Animation (flicker-free)

20

[Max] I need help! / Re: Crashing when rendering animation

« on: 2025-01-14, 15:26:28 »

Thank you Avi, I got a response and it is indeed a Bug.  I think I found a couple of more bugs for other settings so I will report those also.

21

[Max] I need help! / Re: Crashing when rendering animation

« on: 2025-01-12, 19:33:18 »

Okay I created a simplified scene and sent it to chaos. Request #333313

22

[Max] I need help! / Re: Crashing when rendering animation

« on: 2025-01-03, 20:32:40 »

Okay I'll try to create a simple scene, My scene now is complex.

23

[Max] I need help! / Re: Crashing when rendering animation

« on: 2025-01-02, 23:43:44 »

Well I also found if I add even the Render Element "CGeometry_Velocity" so I can do motion blur in post even that will crash out of max.  There is some bug with anything motion blur with Corona 12 Update 1.

24

[Max] I need help! / Re: Crashing when rendering animation

« on: 2024-12-31, 18:51:19 »

I think I figured it out, It seems to be the Corona Camera Motion blur. When activated for Camera and Geometry it crashes during rendering animation out of max. The minute I turned it off it works fine.

25

[Max] I need help! / Re: Crashing when rendering animation

« on: 2024-12-31, 02:59:32 »

Okay so I tried on max 2025 and 2024 crashes out of max on both. Even tried 2 different computers. I think I narrowed it down to animated Corona cameras. It seems to most definitely be the Corona cameras when they are animated. Not sure which setting in Camera are crashing the scene. When I use anything else or just perspective it renders just fine. Minute I go back to camera CRASH. Just like the other scene file. I think it might have to do with animated DOF Value in the camera. Or possibly Environment & Clipping or animated Environment & Clipping.

I noticed that when I try to use IPR and use the Point selector for DOF Focus Value so I can animate it with Auto Key, it doesn't work right. Doesn't keep the measurements or save a key. So maybe there is a bug in the Corona Camera and that is also crashing the app.

26

[Max] I need help! / Re: Crashing when rendering animation

« on: 2024-12-30, 06:35:01 »

Well unfortunately with work I didn't have a chance to rerender that animation. But now I'm finally rendering a new addition and the same issue, crashes right out of max. I'm thinking this is Max issue, I already have some wired problems with Max 2025.3 like selection issues. I'm going to go back to 2024 and see if the new Max is the problem. 2024 Max I never had any issues.

27

[Max] General Discussion / Path guiding?

« on: 2024-12-24, 05:44:19 »

How come Corona never got Path guiding? Vray has it, I've tried it and it makes quite a difference.

28

[Max] I need help! / Re: Crashing when rendering animation

« on: 2024-12-05, 15:04:34 »

Hi sorry, was gone for the holiday. There was a couple of updates for Forest pro and railclone. I did the updates and will render the animation again to see if they were the culprits.

I'll report back my findings.

29

[Max] I need help! / Re: Crashing when rendering animation

« on: 2024-11-25, 07:21:13 »

Well I rolled back to Corona 12 Hotfix 1, same thing. When you render animation it crashes out of max. Not sure if this is a Corona or Max thing. Will have to try Corona 11 next I guess.

30

[Max] I need help! / Crashing when rendering animation

« on: 2024-11-23, 19:08:13 »

I am using Max 2025.3 with Corona 12 Update 1. Works good till you render animation.  Crashes right out of Max. I'm going to downgrade to Corona 12 Hotfix 1 and see if it's to do with the latest Corona.  Anyone else having crashing with latest Corona?