Messages

1

[Max] I need help! / Re: sigershader ccmp

« on: 2017-05-22, 17:18:47 »

If you the registered user at Siger Studio, please send an email to support (at) sigershop.eu
If you try to install the cracked version - don't send the e-mail :)


Okee ⌣»̶·̵̭̌·̵̭̌✽̤̥̈̊‎​•̲̣̥τнänκ чöü •̲̣̥✽̤̥̈̊·̵̭̌·̵̭̌«̶⌣
 Siger.
hopefully it works

2

[Max] I need help! / sigershader ccmp

« on: 2017-05-22, 03:27:03 »

Help...how to install sigershader corona render for max? My install install always fails why? Help my

3

[Max] I need help! / embree

« on: 2014-12-22, 03:07:47 »

want to ask ... ... ... how to use embree on corona

4

[Max] I need help! / Re: setting render corona engine

« on: 2014-10-26, 02:18:39 »

That's what defaults are made for. Best time/quality in most scenes.

Thanks  deadclown
What is my computer's machine capability that does not suport with corona. ... but if not suport, why I used vray can penetrate time 1-2 hours to achieve a resolution of 3000 x 2500 that is clean and sharp. This makes me, the time difference was puzzled as too far away.

5

[Max] I need help! / Re: setting render corona engine

« on: 2014-10-26, 02:10:50 »

Press render and wait?

Your question is kind of vague but if you want to know good render settings to get started then the default ones are really good already and there isn't any reason to really tweak them unless you are trying to achieve something specific.

Thanks nielsh
frankly the same old feel when using the corona. I could take 10 hours to produce a clean and sharp images with a resolution of 3000 x 2500.
While the vray it took me 1 hour ... ... ... but I like corona. because it is very easy in most settings corana camera and lights, the problem I am too long in the end result.

6

[Max] I need help! / setting render corona engine

« on: 2014-10-23, 17:52:24 »

How to create a default rendering for fast and produce a clean and sharp images

7

[Max] I need help! / Re: the pressing time too long

« on: 2014-09-11, 03:27:12 »

Shoud you set GI/AA balance back to 16 and secondary solver to HDCache, render time should get significant improvement, i think.

hai romullus thanks for help me
okay I will try ... hopefully this helps me
thanks romullus

8

[Max] I need help! / Re: the pressing time too long

« on: 2014-09-11, 03:24:49 »

I would say it is more or less good times for such image res and complexity of the scene on single machine as 950.

hai crazyman thanks to help me
you mean I have to replace my engine so what I want to achieve so right
keeps the machine where appropriate do you think?

thanks crazyman

9

[Max] I need help! / Re: the pressing time too long

« on: 2014-09-10, 10:24:44 »

Please give us some more information:

-what is your hardware?
-why did you change GI/AA balance to 5? Do you even know what it does?
-did you just take the scene made in Vray, used a converter and hit "render" without tuning materials manually?

this my hardware
ram 24gb
prosesor intel i7 950
-why did you change GI/AA balance to 5? Do you even know what it does? I just tried from the value of 16 to 5

The amount of GI samples per each sample antialiasing.

Higher values ​​will increase is a sampling of Global Illumination, resulting in cleaner indirect lighting, glossy reflections, refractions and translucency. Lower values ​​will increase is a sampling of antialiasing and therefore improve quality of fine geometry edges, Depth of Field, and Motion Blur.

Setting this value under 2 or above 64 is not recommended.
thanks maru

10

[Max] I need help! / Re: the pressing time too long

« on: 2014-09-10, 09:56:31 »

hi all...... i have a problem why i use exterior rendering corona render takes a long time... to produce an image resolution of 3000 x 2500 is clean without any noise it took me 12 hours more...what's wrong with default i... please help my ..thanks
 

this results in my rendering ... i took almost 12 hours more.. why is this happening to me.. its me tomorrow ..try again ..the time need more extrim 26 hours...can imagine in time for so long.

11

[Max] I need help! / the pressing time too long

« on: 2014-09-10, 09:34:40 »

hi all...... i have a problem why i use exterior rendering corona render takes a long time... to produce an image resolution of 3000 x 2500 is clean without any noise it took me 12 hours more...what's wrong with default i... please help my ..thanks