Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - PROH

Pages: 1 [2] 3 4 ... 82
16
Thank you.
I use hotkeys instead. It works very well, and simplifies the use of edgetrim enormous.

Great script :)

17
Thank you :)

I'm running the script without hotkeys, and it adds Edge Trimming map(s) without problems. But I can't get it to remove them again.

Is this possible without hotkeys?

Corona 9
Max 2020

18
It's insane. Reminds me of AD!

19
It's sad to be forced to pay an extreme extra amount without any warning (30 days is worthless compared to the pricehike).

I can't remember any other situation where I have felt so screwed over as now - and that's comming from the Corona team - who had a reputation of beeing userfriendly and fair.

It's not only Chaos who's having a hard time now - it's also their users.

I don't like this at all, and find it totally unacceptable.

20
Really confusing!
First I got an email telling me, that my subscription has changed, but the prize is the same. Then 1 and a half hour later, I got an email telling me that my prize is gone up, and now Ondra says something I don't fully understand...
What's going on? Could we please be correctly informed in a way that can't be misunderstood.
Thanks.

21
[Max] General Discussion / Re: washed out cosmos assets
« on: 2022-10-05, 12:16:32 »
I agree. This is a Chaos service that should be tailored for their products.

22
[Max] General Discussion / Re: washed out cosmos assets
« on: 2022-10-05, 11:56:52 »
But the problem isn't only regarding materials. A lot of the 3d people are coming in with broken meshes, even though the same models from the source vendor are fine.
Chaos Cosmos assets clearly need some love :)

23
Haven't tried it yet. But it sounds extremely cumbersome to make this work. Imagine several objects with a multimaterial each.
That's not userfreindly.

25
[Max] I need help! / Re: Corona Light slows down Viewport
« on: 2022-09-12, 17:14:19 »
Hi. Have you tried to set properties to "show as box"?

26
[Max] I need help! / Re: License can't be activated
« on: 2022-08-19, 00:18:46 »
I don't know for sure. But I think there is a  phone number for urgent needs somewhere on the site.

Good luck

27
[Max] I need help! / Re: License can't be activated
« on: 2022-08-18, 23:36:02 »
Hi. Had this problem a couple of days ago. You need to contact Chaos so they can fix it.

It's a shame how they mess up Corona license :(

28
[Max] Resolved Bugs / Re: Displacement issue (problem)
« on: 2022-08-17, 19:12:26 »
OK. Now I have done some testing myself, and can confirm that displacement on large scale is problematic with Corona.

My test was designed to see how far away you can see displacement sized around 20-25 cm, and in both 4k and 6k renderings I could still see it at 1km distance, even with the denoiser on (Corona). Pictures attached.

But at 8k the problems begin. There is lots of artifacts in the render, and Corona gives a warning about low RAM (I only got 64Gb). Low RAM however should only cause a slow render, and NOT give artifacts.
I have tried to locate the problem, and one thing I noticed is, that when the "Primitives displac." number goes higher than 1.000 M I start to have artifacts.

Hope it helps.

29
[Max] Resolved Bugs / Re: Displacement issue (problem)
« on: 2022-08-16, 17:33:39 »
Sorry for the wording. Is autobumb on or of?

30
[Max] Resolved Bugs / Re: Displacement issue (problem)
« on: 2022-08-16, 10:45:02 »
What denoiser are you using, and how is your bump and autobump set up?

Pages: 1 [2] 3 4 ... 82