Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - tallbox

Pages: 1 ... 7 8 [9] 10
121
I am getting problems when using only render region and DR without any scattered objects.

122
Gallery / First commersial project with corona
« on: 2015-05-21, 08:04:46 »
Hello guys,
this is my first attempt to finish commercial project with corona v1.
I've worked on this 5 hours + render 6 hours on 1 pc. Somehow dof are bit messy and some materials (bed for example), but i'm satisfied with the lighting.
Don't judge me too hard i am still beginner with corona )))

Cheers,
G.

124
[Max] I need help! / Re: Distributed not working too good
« on: 2015-04-20, 11:31:35 »
Today i was rendering my test scene (see below) with Corona DR on 3 slaves. I try to render on region part of the scene with DR and after 2 min. i realized that DR could not work in region at least properly. I got Error and non of them working properly. After that i tried to render the scene again in Full aspect and everything was normal. Maybe that is an issue or bug.

G.

125
[Max] I need help! / Re: Slow render and lots of noise
« on: 2015-04-18, 17:59:27 »
So here are an update of my process.
I re-edited scene and rays goes up to 2,5 mil.
I had a problem also with corona DR - all my slaves didn't want do render anything. I read almost every forum threads here and nfo files - finally slaves still giving me these ping errors but all they DO rendering job!

Regards,
G.

126
Hello guys, i have a question about DR rendering folder on main machine.
Is there a way to change that folder, because after last rendering job my C:// was with 50 gig. more files.


127
[Max] I need help! / Re: Distributed not working too good
« on: 2015-04-17, 19:51:23 »
So i did my licences on all render slaves as in the nfo. pages but corona dr. still giving me > Got discovery ping> Replying to discovery ping from main pc?

128
[Max] I need help! / Re: Slow render and lots of noise
« on: 2015-04-17, 15:17:21 »
So generally after maru's comment i edited almost all materials (ior and albedo)and light rays jump up from 0,8k to 1,6-1,8 mil.? Also i removed all lights with ies and scene was lit only with corona light as spheres.
I will try to improve more - to go above 2 mil.

129
[Max] I need help! / Re: Slow render and lots of noise
« on: 2015-04-15, 15:40:33 »
Hello maru,
yes the scene was converted from vray 3.1 scene, that we work in our studio. I just get that scene and used corona converter to test some things. I will check all things that you mention.
Thank you.
I will write later.

130
[Max] I need help! / Re: corona to vray converter
« on: 2015-04-15, 15:23:54 »
Thanks

131
[Max] I need help! / Re: Slow render and lots of noise
« on: 2015-04-14, 22:36:46 »
I found second bug - after adjusting few times gradient map at opacity slot (max 2015) whole max crash. Scene was simple kids room with few objects.

132
[Max] I need help! / Re: Slow render and lots of noise
« on: 2015-04-14, 14:42:46 »
I will today later

133
[Max] I need help! / Re: Distributed not working too good
« on: 2015-04-14, 10:48:08 »
I will do it today.

134
[Max] I need help! / Re: Distributed not working too good
« on: 2015-04-14, 09:03:47 »
I've got same Error - corona DR searching for ping all the time and that's it. I don't want to re-install max on 4 pc-s? Any other solutions?

135
[Max] I need help! / Re: Slow render and lots of noise
« on: 2015-04-14, 06:56:48 »
I tried with deleting all bitmaps on wall and leave it on diffuse colours. Light rays was even lower than previous render.
PS: When i'm doing render regions light rays are much more and stable 1,1 - 1,2 mil.

Pages: 1 ... 7 8 [9] 10